Internal mount set for EchoSounder oscillator In hulls, made of FRP, the transducer can be mounted inside. It is installed in the oil-filled tube. Dimensions: Ø 53 mm, H 86 mm. A second nut for the Nasa EchoSounder transducer is included. When using this kit, you don´t need to drill a hole in the hull of FRP yachts, when you mount the transducer.
Interenal mount set for depth transducer	order here

	Extension set for EchoSounder oscillator In yachts with wooden hulls, FRP -Sandwich-construction or steel ships, the transducer needs direct contact to the water. The streamlined plastic part protects the oscillators head and prevents turbulences. The included sealing compound and Nirosta- screws provide a waterproof mounting. Dimensions: L 190 x W 85 x H 43 mm.
Extension set for depth transducer	order here

	EchoSounder transducer 60mm Suitable for all EchoSounders with an oscillating frequency of 150 kHz, e.g. NASA, Seafarer. Thread length: 60 mm .
EchoSounder transducer 60mm	order here

	Log transducer Complete, or spare parts for Nasa Clipper and Cruiser Speed.
Log Transducer incl. Mounting flange for through- hull fitting	order here
Log Transducer like above, but without mounting flange	order here
Mounting flange for through- hull fitting, without Log Transducer	order here
Spare-Paddlewheel for Log Transducer	order here

	Wind transducer Complete, or spare parts for Nasa Clipper Wind instruments.
Mast unit, complete, forNASA-Wind instruments.  With 15 meter cable and plug	order here
Spare Wind vane for wind direction in white	order here
Spare-Wind wheel for Wind force	order here

	NMEA-Fluxgate-Sensor Suitable as a spare part for all NASA-Compass systems with NMEA-Input and as NMEA-course transducer e.g. for Auto pilots. Stabiles und gegen Feuchtigkeit versiegeltes Gehäuse. Gimballed Fluxgate- course transducer, up to +/- 40°. NMEA 0183 Output. Connection cable with bare wires, 10 m long. Dimensions: 82 mm x 68 mm x 40 mm.
NMEA-Fluxgate-Sensor	order here

	Housing for NASA-Clipper instrument series Plastic housing for 2 Clipper-instrument series. It can be mounted at the mast or the steering column with the matching mounting kit. Included in delivery. Cable screws and general mounting set out of stainless steel and two connection adapters (EchoSounder/Log). Dimensions: W 260 x H 130 x D 55 mm.
Housing for NASA-Clipper instrument series	order here

	swivel mount for instruments and sounder This mount can be fixed downstairs on the wall with the display. you can move the arm by 180° to see the instrument in the cockpit by the helmsman. A screw fixes the position. Built in tough, black polystyrol.
swivel mount	order here

 

	Acrylic glas bracket Useful acrylic glas bracket for a stylish wall- or table mounting, tiltable.  Suitable for NASA Weatherman and NASA Clipper Weather decoder instruments.
Acrylic glas bracket	order here

 

	Extension cable for Nasa Clipper, Cruiser Instruments and Clipper Weather receiver.
for NASA-Wind- and Compass systems, 5 m	order here
for NASA-Wind- and Compass systems, 20 m	order here
for NASA EchoSounder and Log, as well as antenna cables of NASA-Weather- and Navtex-receiver, 7 m.	order here

 

	Angle bracket for oscillator In rubber- or fishing boats you can put the transducer in the plastic bracket, which is screwed on the transom. After leaving the boat, the transducer can be taken away.
Bracket for sounder	order here

antenna rail mount for the nasa weather receivers

order here

back